Screwing Metal Roofing. Correct & Incorrect Way Of Fastening A Metal Roof + Pre-Drill + Screw Guns

Screwing Metal Roofing. Correct & Incorrect Way Of Fastening A Metal Roof + Pre-Drill + Screw Guns

605,634 View

Learn About Screwing Metal Roofing And Fastening A Metal Roof. This screw and fastener installation video covers the correct & incorrect way to fasten a metal metal roof.

Install video that covers screw and fastener installation instructions for exposed fastener panels on a metal roof. Learn the incorrect and the correct way to fasten a metal roof.

The single biggest reason for metal roofing leaks is Incorrect screw attachment. Your roof will have thousands of screw penetrations and it's important you know the correct way to install the screws on your metal roof.

00:00 What is correct and incorrect way to fasten a metal roof?
01:00 How to install metal roofing fasteners. Screwing metal roofing.
02:11 What is swarf?
02:38 How to use a screw gun for metal roofing
04:01 How to pre-drill metal roofing panels
05:57 How to snap a chalk line for a metal roofing panel


In This Video We Cover
Installation of metal roofing screws
The Incorrect And Correct Way To Fasten A Metal Roof
How tight should metal roof screws be?
What do I do if I over-tighten metal roofing screw?
Do's and don'ts of fastening metal roofs
Removing the metal shavings
Do I need to remove the metal shavings from my metal roof?
How do I remove the metal shavings from my metal roof
Pre-Drilling Screw Holes
Using The Correct Tools
Chalk Lines

Step by step video that details how to incorrectly and correctly fasten corrugated metal roofing, R Panel, 7.2 Panel, U Panel, or Ag panel. Not intended for standing seam panels.

Visit Our WEBSITE


Visit our LEARNING CENTER


WRITTEN GUIDE - Metal Roofing Fastener Installation


Download Our INSTALL GUIDES
7/8" Corrugated


R Panel/PBR Panel


Western Rib/7.2 Panel


It is important to drive or install the screws correctly. This is a really simple procedure, but quite often it is done incorrectly. If you mess this up your roof will leak, so taking the time to correctly fasten the screws is exceptionally important. This video will be an excellent guide that will clearly demonstrate the correct way to tighten a screw.

The screws that you will be using will have a rubber washer with a metal cap. The rubber washer is just a bit smaller than the metal cap. You want to tighten the washer so that it spreads to the edge of the metal cap and not past the metal cap. When you tighten the screw it’s critical that you don’t drive it too far.

It’s a natural reaction to exert too much pressure and tighten the screw as much as possible. This will over compress the washer by expanding it too much and breaking the washer. If this happens back out the screw to relieve some of the pressure. If you over-tighten the screws then they might leak and will also need maintenance sooner.

Conversely, it is common to under-tighten the screw. The easiest way to determine if the screw is too loose is to see if you can spin the washer. If the washer spins, then the screw is too loose and should be retightened. You will develop a feel for fastening the metal panels correctly, but just pay close attention to ensure that the screws are installed correctly.

Screws Should Be Installed Straight And Not Sideways

Screws that are installed sideways or tilted will not permit the rubber washer to seal correctly. This will create a possible leak point. If you notice this has happened then back the screw out and redo so that the screw is straight.


FOLLOW US ON SOCIAL MEDIA:

FACEBOOK:
INSTAGRAM:
TWITTER:
LINKEDIN:
HOUZZ:
PINTEREST:
YOUTUBE:

Visit Our WEBSITE


Visit our LEARNING CENTER


Read More
By: Metal Roofing Learning Channel®
Title: Screwing Metal Roofing. Correct & Incorrect Way Of Fastening A Metal Roof + Pre-Drill + Screw Guns
Sourced From: www.youtube.com/watch?v=zpDAeqpNPFc



_______________